# HUGE Design Flaw in Curtain Lights! (CRAZY difference after fixing) Source: https://www.youtube.com/watch?v=U4QphhY84f4 Recap page: https://rapidrecap.app/video/U4QphhY84f4 Generated: 2025-12-27T15:05:40.466+00:00 --- ## Quick Overview The major design flaw in the Govee Curtain Lights Pro, causing the 960 LEDs to appear crooked when animated, is that the individual LED beads are not consistently facing outward, with some facing the wall and others facing out, a problem solved by meticulously using adhesive clips and a laser level to ensure all strands face the same outward direction. **Key Points:** - The Govee Curtain Lights Pro, featuring 960 RGBIC LEDs, suffers from a design flaw where light patterns appear distorted because individual LED beads are inconsistently oriented (some face the wall, others face out). - The solution involves using small, clear adhesive clips (found on Amazon) to manually straighten and lock approximately 30 strands at the bottom, ensuring all LEDs face outward. - The creator tested three methods for securing the bottom of the strands: standard sticky pads, Gorilla Clear Glue, and finally, double-sided carpet tape. - The initial method using 3M sticky pads failed because the lights' material did not adhere well to the pads. - Gorilla Clear Glue was rejected because it was 'incredibly messy' and the curtain material did not stick well to it either. - Double-sided carpet tape proved successful, allowing the creator to secure the bottom guide strip flat against the wall, resulting in perfectly straight light strands when animated. - A comparison shows the 'new' (fixed) setup has sharp, defined light patterns (like the Matrix code effect) while the 'old' (unfixed) setup shows blurred, distorted patterns due to the uneven LED orientation. ![Screenshot at 00:26: The initial state of the Govee Curtain Lights installation showing that the bottom of the light strands lack sufficient weight, causing them to hang crookedly and not align properly.](https://ss.rapidrecap.app/screens/U4QphhY84f4/00-00-26.jpg) **Context:** This video addresses a common aesthetic issue encountered when installing Govee Curtain Lights Pro, which use 960 individual LEDs arranged in vertical strands. The creator noticed that despite being stretched out and aligned according to the laser level, animated patterns displayed on the light curtain appeared crooked or blurred, indicating a physical orientation problem with the light beads themselves rather than a software or alignment error. ## Detailed Analysis The video details a fix for a significant design flaw in the Govee Curtain Lights Pro (960 LEDs) where the light patterns appear distorted due to inconsistent LED bead orientation. The creator first observed that the strands hung unevenly because the bottom lacked weight, leading to some LEDs facing the wall and others facing outward (00:26). The initial attempt to fix this involved using 3M adhesive clips, but the material of the curtain lights did not stick well to the pads (00:42-00:46). The next attempt using Gorilla Clear Glue was deemed too messy and also failed to adhere properly to the light material (04:06-04:22). The successful solution involved purchasing 1/16th inch thick plastic wainscot wall panels from a hardware store to serve as a backing strip (02:09-02:14). The creator then used small, clear adhesive clips to secure about 30 strands to this backing strip, ensuring they were perfectly straight and facing outward, using a laser level as a guide (02:47-03:38). The final comparison demonstrates that with the strands correctly oriented using this method, complex animations display sharply, whereas the original configuration resulted in significant blurring and distortion (05:04-05:29). ### Identifying the Flaw - Curtain light strands hang at crooked angles because LED beads are not uniformly facing outward, causing visual distortion in animations - The issue persists even when strands are stretched straight using a laser level. ### Failed Fix Attempts - Initial attempts using 3M adhesive backing pads failed because the light material would not stick - Gorilla Clear Glue was too messy and also failed to secure the strands properly. ### The Successful Solution - The creator used 1/16th inch thick plastic wainscot wall panel as a rigid backing strip, secured near the floor with double-sided carpet tape - Small, clear adhesive clips were used to manually straighten and lock the bottom of every strand to this strip, aligning them perfectly outward. ### Final Results Comparison - A side-by-side comparison shows the 'new' (fixed) lights displaying crisp, defined patterns (e.g., Matrix code, logos) compared to the 'old' (unfixed) lights which show blurred, wavy patterns, especially noticeable during dynamic animations. ![Screenshot at 00:01: Govee Curtain Lights Pro box detailing 960 LEDs and smart home compatibility.](https://ss.rapidrecap.app/screens/U4QphhY84f4/00-00-01.jpg) ![Screenshot at 00:34: The creator kneeling on the carpet, applying 3M sticky pads to a white strip intended to hold the bottom of the light strands.](https://ss.rapidrecap.app/screens/U4QphhY84f4/00-00-34.jpg) ![Screenshot at 01:04: Side-by-side comparison showing the 'old' \(right\) light pattern is blurred compared to the 'new' \(left\) pattern, demonstrating the initial problem.](https://ss.rapidrecap.app/screens/U4QphhY84f4/00-01-04.jpg) ![Screenshot at 02:11: The creator holding up a large, flexible white plastic wall panel purchased from a hardware store as a potential solution backing.](https://ss.rapidrecap.app/screens/U4QphhY84f4/00-02-11.jpg) ![Screenshot at 05:04: Final comparison showing the 'new' \(left\) setup with sharp, clearly defined green lights versus the 'old' \(right\) setup with noticeable light bleed and blurring.](https://ss.rapidrecap.app/screens/U4QphhY84f4/00-05-04.jpg)